Applying self-adhesive wallpaper in this way will prevent bubbling! Surprisingly, many people get it wrong from start to finish!
Source:
|
Author:akadeco
|
Published time: 2024-02-04
|
89 Views
|
Share:
To make wall decoration look good and to facilitate a quick installation process, self-adhesive wallpaper has emerged on the decoration market. This product does not require additional glue and can be directly applied to the wall. It not only offers certain features like sound absorption, heat insulation, mold and bacteria resistance, but also comes in a rich variety of colors and patterns, ensuring safety and environmental protection. However, according to an experienced decorator, many workers apply it incorrectly from start to finish, often resulting in the wallpaper bubbling. So, how exactly should self-adhesive wallpaper be applied?
1. Carefully inspect the wall surface. If there are holes or raised areas, fill them with putty and smooth the wall with a scraper. To ensure successful adhesion, the surface must be kept dry and free from mold, grease, or other impurities. If the surface of the object to be pasted is rough, it must be sanded smooth and wiped down with water or a neutral detergent to prevent it from affecting the overall effect.
2. Measure the dimensions of the wall accurately. When measuring the wallpaper based on the wall area, make sure that the length of the wallpaper extends about 125px beyond the actual area to be covered at both the top and bottom.
3. Separate the film from the backing paper, then apply it from top to bottom along the wall, gently pressing from the center outwards to remove wrinkles. Larger air bubbles can be pricked with a needle to release the air.
4. When encountering power switches or outlets, cover them with the wallpaper first, then smooth it out with a wooden brush, and cut a cross over them diagonally with a utility knife. Use a wooden brush or scraper to press against the edges of the switch, then trim the excess wallpaper along the edges of the switch with a utility knife.
5. If dealing with patterned wallpaper that needs to be joined, find a position where the patterns match at the seam between two wallpapers, overlap them by about 300px, and once the entire wallpaper is aligned, press it down with a scraper and cut off the overlapping part with a sharp knife.
6. Finally, when dealing with wallpaper around doors and windows, follow the same method as for handling wallpaper around power switches.
To make wall decoration look good and to facilitate a quick installation process, self-adhesive wallpaper has emerged on the decoration market. This product does not require additional glue and can be directly applied to the wall. It not only offers certain features like sound absorption, heat insulation, mold and bacteria resistance, but also comes in a rich variety of colors and patterns, ensuring safety and environmental protection. However, according to an experienced decorator, many workers apply it incorrectly from start to finish, often resulting in the wallpaper bubbling. So, how exactly should self-adhesive wallpaper be applied?
1. Carefully inspect the wall surface. If there are holes or raised areas, fill them with putty and smooth the wall with a scraper. To ensure successful adhesion, the surface must be kept dry and free from mold, grease, or other impurities. If the surface of the object to be pasted is rough, it must be sanded smooth and wiped down with water or a neutral detergent to prevent it from affecting the overall effect.
2. Measure the dimensions of the wall accurately. When measuring the wallpaper based on the wall area, make sure that the length of the wallpaper extends about 125px beyond the actual area to be covered at both the top and bottom.
3. Separate the film from the backing paper, then apply it from top to bottom along the wall, gently pressing from the center outwards to remove wrinkles. Larger air bubbles can be pricked with a needle to release the air.
4. When encountering power switches or outlets, cover them with the wallpaper first, then smooth it out with a wooden brush, and cut a cross over them diagonally with a utility knife. Use a wooden brush or scraper to press against the edges of the switch, then trim the excess wallpaper along the edges of the switch with a utility knife.
5. If dealing with patterned wallpaper that needs to be joined, find a position where the patterns match at the seam between two wallpapers, overlap them by about 300px, and once the entire wallpaper is aligned, press it down with a scraper and cut off the overlapping part with a sharp knife.
6. Finally, when dealing with wallpaper around doors and windows, follow the same method as for handling wallpaper around power switches.
